Cobra 20A FPV Multirotor ESC

Write A Review

Cobra 20 Amp 2-4 Cell FPV Multirotor ESC

Out Of Stock

Regular Price: $16.99

Special Price $8.49


Cobra Multirotor Speed Controllers are designed to be the perfect compliment to the Cobra Multirotor motors, but can also be used with virtually any brand brushless motor. These speed controllers come with the latest BL-Heli firmware installed, and are able to accept refresh rates of up to 600 Hz from your flight controller board. They come set up and ready to go from the factory, so in most cases, no programming of any kind is required. If the user wishes to upgrade the firmware, make changes, or switch to the new One-Shot firmware, this can be done with the optional USB ESC Programmer, which is available separately. This ESC uses the Atmel MEGA8A microprocessor, so make sure that the correct firmware is installed when changes are made.

The Cobra FPV Mini Speed Controllers do not provide BEC voltage to power your receiver or servos. A separate battery or BEC circuit is required when using these speed controllers. In most cases, you can use a power distribution board with a built-in 5 volt switching regulator circuit. The control lead on this ESC only has the Signal and Ground connections, so there is no need to pull the red wire out of the connector.

The Cobra 20A Mini FPV Multirotor ESC comes with pre-tinned input and output leads, which can be cut as needed for installation purposes. The battery leads on the ESC are 18 AWG, and the motor leads are 20 AWG. The assembled weight of the Mini 20 amp ESC is 10.0 grams. However, many weight conscious pilots want to strip down the ESC's to get the weight to a bare minimum. The table below gives the weights of each of the components in the speed controller as a reference.

Please Note: If the ESC is modified to reduce weight, the user will do this at their own risk. Because we cannot control the quality of the soldering operations necessary to remove components, any changes to the ESC will void the factory warranty.

Cobra 20 Amp Mini FPV Multirotor ESC Weights
 Overall weight (With Lead Wires) 10.0 grams (0.353 oz)
 Bare Circuit Board weight 2.0 grams (0.071 oz)
 Input Lead Weight 2.1 grams (0.074 oz)
 Output Lead Weight 2.1 grams (0.074 oz)
 Control Lead Weight  2.2 grams (0.078 oz)
 Heatshrink Cover weight 0.6 grams (0.021 oz)
 Capacitor weight 0.6 grams (0.021 oz)
 Heat sink weight 0.4 grams (0.014 oz)

Cobra Multirotor Speed Controller Features

• Easy Set-up and Operation
• Throttle Range automatically detected and set for smooth, linear throttle response
• 600 Hz refresh rate is compatible with most flight controllers on the market
• ESC's ship with BL-Heli Firmware which can be switched to One-Shot if desired
• Optional USB programming interface available for easy Firmware updates
• Safe Start-Up: The ESC will not arm until the throttle is in the idle position
• PWM Frequency is set to 20KHz for best operation on a wide range of motors
• Over Temp Protection: Shuts down the ESC output if temperature exceeds 230F (110C)

Cobra 20 Amp Mini FPV Multirotor ESC Specifications
 Weight (With Lead Wires) 10.0 grams (0.35 oz)
 Weight (Bare Circuit Board) 2.0 grams (0.07 oz)
 Max Continuous Current 20 Amps
 Burst Current rating (15s) 25 Amps
 ESC Microprocessor Atmel MEGA8A
 Operating Voltage Range  6 to 16 Volts
 Number of Li-Po cells 2 to 4 cells
 BEC Output None (Opto)
 ESC Size (Inc. Caps, in mm) 38 x 13 x 8
 ESC Size (Inc. Caps, in inches) 1.50 x 0.51 x 0.31

For more information about this product and the rest of the Cobra Motors product line, please check out the Cobra Brushless Motors web site.
Cobra 20A Mini FPV Multirotor ESC

Write A Review

Only registered users can write reviews. Please log in or register

Customer Reviews

This product has not been reviewed. You could write the first review.